PEMANFAATAN MATERIAL LOKAL DALAM PEMBUATAN ASPAL PORUS TIPE AC-WC YANG AMAN DAN RAMAH LINGKUNGAN Amiruddin, Ibrahim, Ika Sulianti, Agus Subrianto

Main Article Content

Redaksi Tim Jurnal

Abstract

Surface of highway pavement is wet during rain and drowned by stormwater. This situation can makes slip of vehicle wheels and causes an accident. Porous asphalt is a new generation in flexible pavement. Porous charactheristic can be obtained by using less fine aggregates comparing the normal one so it has more voids. We can expect the pavement has higher skid resistance and its voids can be functioned as drainage in mix. This type of pavement developement also strongly depends on availability of the approriate local material for that we can produce a good performance porous asphalt which is described in this paper. Consideration of  so many problems can be taken apart, the research is limited in modification design of asphalt concrete wearing course using porous asphalt mix exploits South Sumatera aggregates. After investigatives classification of aggragates, the fine aggregates (sand) can be reduced significantly to obtain a large amount of voids by 6.1% asphalt used. However, this porous structure also causes defect, mainly the stability degradation in mix. So the future research will continue to formularize a better stability performance from pavement variety expected

Downloads

Download data is not yet available.

Article Details

Section
Articles

References

[1] Andiyanto. C. (2010). Pemilihan Teknik Perbaikan Perkerasan Jalan dan Biaya Penanganannya. Undergraduate thesis. Universitas Sebelas Maret. Malang
[2] Departemen Pekerjaan Umum Revisi 3 Divisi VI. (2010). Spesifikasi Pengujian Aspal. Yayasan Penerbit Pekerjaan Umum.
[3] Hardiyatmo H.C. (2009). Pemeliharaan Jalan Raya. Gadjah Mada University Press. Yogyakarta.
[4] Katsuji Nishijima, Shiego Higashi and Masaki Ikeuchi. (2009). Development of re-paved porous asphalt pavement method for reconstructing existing dense graded asphalt pavement into porous asphalt pavement using the in-place surface recycling method, Proceeding of 13th Conference of the Road Engineering Associationof Asia and Autralasia (REAAA), 9-15.
[5] M. Miradi, A.A.A. Moleenar, M.F.C van de Ven. (2009). Performance modeling of porous asphalt concrete using artificial intelligence, Road Materials and Pavement Design. ICAM 2009, pp.263-280.
[6] SNI 06-2432-1991, Metoda Pengujian Daktilitas Bahan-Bahan Aspal. Pusat Litbang Jalan Dan Jembatan. Bandung.
[7] SNI 06-2433-1991, Metoda Pengujian Titik Nyala Dan Titik Bakar Dengan Alat Cleveland Open Cup. Pusat Litbang Jalan Dan Jembatan. Bandung.
[8] SNI 06-2434-1991, Metoda Pengujian Titik Lembek Aspal Dan Ter. Pusat Litbang Jalan Dan Jembatan. Bandung
[9] SNI 06-2441-1991, Metoda Pengujian Berat Jenis Aspal Padat. Pusat Litbang Jalan Dan Jembatan. Bandung.
[10] SNI 06-2456-1991, Metoda Pengujian Penetrasi Bahan-bahan Bitumen. Pusat Litbang Jalan Dan Jembatan. Bandung.
[11] Sukirman S. (2010). Perencanaan Tebal Struktur Perkerasan Lentur. Nova. Bandung.
[12] Sukirman S. (2003). Beton Aspal Campuran Panas. Penerbit Granit. Jakarta
[13] Sukirman S. (2010). Perencanaan Tebal Struktur Perkerasan Lentur. Nova. Bandung.